How to Open Ford Focus Bonnet When Lock Is Broken
The content of the article:
How to open the hood of a Ford Focus. The Ford Fokus has a lockable bonnet that is not easy to open without first knowing it.
How to open the hood of a ford. As we can see in the photo above, you need to insert the bonnet ignition key into the lock box under the "Ford" logo on the radiator grill, which must be turned up and left. Ford Focus history.
Curious! Throughout its history, the company logo has changed 8 times, while the name Ford itself has never disappeared from the emblem.
The Ford Focus is equipped with a lockable bonnet. The opening procedure is somewhat original and difficult in the absence of initial information.
We heat the screwdriver over the flame and try to drown the hot tip in the plastic latch. Either rusted, or just fell off, although maybe something else. Home Consultation with the author. Next, you need to do the following: One of the most common malfunctions of this mechanism on a Ford Focus is a situation when the rod pops out of the groove.
How to open the hood on Ford Focus 2
There is no cable here, and it is not possible to open it from the passenger compartment, at least in this configuration. Having inserted the key, as indicated in the instructions in the photo, you can see, first turn it counterclockwise to the left half a turn, while simultaneously pulling the hood up, and immediately turn the key half a turn clockwise to the right - the hood is open.
Since the radiator grille is located far from the hood lock itself, at the time when we turn the key, we turn this red arrow rod, which, in fact, opens the lock. As a rule, the cylinder of the bonnet lock breaks. People, as a rule, immediately run screaming - the hood lock has broken, buy a Ford Focus hood lock! But, it breaks, neither the lock nor the rod is broken, this rod in the photo above simply jumps out of the groove. As a rule, the fixing antennae of the gimbal socket, which you see in the photo above, wears out or breaks.
And the cardan is already jumping out of its place at every turn of the key and trying to open the hood. To do this, either change the lock cylinder, or insert the cardan into place and wrap it with electrical tape, or even better - solder the cardan and the larva.
Then I found how to open it with a screwdriver, put it on top of this cable and pressed hard on the white core, while the comrade turned it with a key at that moment. The hood opened, the mechanism was assembled, everything worked ... until recently. Again the same story, only now the screwdriver does not help: he has suffered himself, friends too - it does not go and that's it. I found the topic of how men fry the same white core with a red-hot screwdriver and then this screwdriver serves as a key. Only no one says how before that they removed this cable traction, so that then there would be right in the center to poke.
I nervously pulled this cable, it split into two halves: the upper rubber part remained on the side of the key, and the iron center on the side of the motor. Like the author, he came across a cardan that jumped out of the groove, and to his surprise, he discovered an even easier way to open the hood without a key. In the picture showing the inserted screwdriver, the protective plastic grill is clearly visible.
This grill can be partially pulled out of its fastening grooves with bare hands and without damage, and then, passing through the gap formed from below between the machine body and this grill, pass your hand or hands and insert the cardan into the groove. Or, by inserting it into one groove, pull it out of the mask, scroll it in one direction or the other, and voila, the hood is unlocked.
Home Consultation with the author. Renault Sandero trunk lock repair. How to open a jammed lock. Removal and replacement of spark plugs. Is it possible to remove the crankcase and bumper protection from below to reach the lock? Add a comment Cancel reply. Proudly powered by WordPress.
How to open a Ford trick and not go to jail
I drive Focus
Kharkiv region, Energodar
How to open the hood on Ford Focus 2
Here is blah-blah-blah about the second generation of the Focus, and then I'll move on to the main question: How does the hood of the Focus 2 open ?!
As you already know, the Ford Focus 2 hood lock is located under the badge on the radiator grill and cannot be opened from the passenger compartment. This is a very unusual solution and it sometimes gets buggy. The pull of the bonnet lock is weak and periodically pops up, so it will not work to open it with a key and you will need improvised means.
What did you think when the hood didn't open? The larva broke? Perhaps, but it seems to me that it just flew off or jammed the lock bracket.
First, see how easy it is to open the hood Focus 2
They turned the key half a turn to the left, lifted the cover, and then clockwise to the right. Simple? But you should have noticed the lack of a key. Yes, they did it without a key)
How to open the hood if the lock bracket has flown off on Ford Focus 2
In order to open the hood without a key, you will need to prepare a special device or a long flat screwdriver.
We insert it through the radiator grill into the groove for fastening the rod and repeat the usual opening of the lock.
The video below clearly shows how to do this.
If the mount does not look like this, then a little more hemorrhoids, but everything is also very simple.
We turn on the music louder. We will swear loudly and more than once.
We pull out the cable as shown in the photo:
Insert the screwdriver and press just above the cable.
This is the place I was looking for for half an hour.
After pressing in the correct place, you will hear a click. After clicking, do not remove the screwdriver from this place, as you will need to quickly scroll the key first to the left and then to the right. I must emphasize when you find the correct screwdriver position and the right amount pressure, the hood will suddenly pop out on the left turn of the key, and then open on the right, it is important not to be too happy and stop the pressure with a screwdriver. If you do this, then you will lose touch and you will have to start all over again.
Car repair and maintenance
Repair and maintain your car
How to open the hood of a Ford Focus 2
There are a few more questions on this topic: "How to open the hood without a key", " Open the hood"Ford Focus 1", "How to open the hood Ford mondeo"," How to open the hood of a Ford ", etc. I will show an example of my Focus 2.
How to open the hood FF2
Hood ford focus 2 Opening Ignition. The cable is missing and cannot be opened from the cab (at least in this configuration). First of all, we will understand how the Ford Focus hood lock works. Ford Focus 1 bonnet lock and Ford Focus 2 bonnet lock.
How to open the hood of a Ford
Ford hood lock
As seen in the photo above, you need to insert the ignition key into the bonnet in the Ford-branded lock box on the grille that needs to be raised to the left. Insert the wrench according to the instructions (seen in the photo), turn it counterclockwise (left) halfway, pull the hood up and immediately turn the wrench clockwise (right). the hood is open.
Locking hood Ford Focus 1
See the photo above. Since the grill is far from the hood itself, and we turn the key, we return it (red arrow) to the bar that actually opens the lock. Typically, the hood that blocks the larva breaks. People tend to cry immediately. the hood lock is broken, buy a Ford Focus Lock hood! But it will break, neither the lock nor the rod is broken, this ejector (pictured above) will simply pop out of the slot.
Read also
The alternator provides the current for electricity consumption while the engine is running and maintains battery power. The generated power of the generator depends on the speed crankshaft... When the engine is running at Idling, generator ra ...
Xz106 ›Blog› How to Measure Engine Compression One of the reasons for a decrease in vehicle power is a decrease in engine compression. If the compression is normal, the engine is good. However, its decrease indicates a possible malfunction ...
Chevrolet CruzeThis is why the worldview is a little tainted by Japanese realities. But now, a week ago on the weekend, he took Cruz to go, go back and forth, bring this / that. The device appeared in the basic configuration - 1.6, "pen". The machine works ...
Overview new Toyota 2018 Camry, the new Toyota Camry - photos and videos, prices and equipment Toyota sedan Camry, specifications and feedback from the owners of the next 8th generation of the world's most popular four-door car. Official world ...
Checking and replacing the ignition coil Non-contact ignition systems with distributor Models with an ignition coil built into the distributor 1. Disconnect the negative cable from the battery.If your car stereo is equipped with a protective cover ...
But don't worry! You can manually open the hood by squeezing and rotating the stem from the bottom of the machine, disassembling the engine guard (see two photos below)
Fix the hood of the Ford Focus 2
How to open the hood Ford focus
How to open hood if the lock bracket flew into Ford Focus 2... Be aware of the problem!
How to open the hood in Ford Focus 2 if the lock is broken
How to open hood on the Ford Focus 2 if the lock is broken. in this video No the larva works. There is no attraction to the castle.
How to open the hood of a Ford
Or, pass a long flat screwdriver through the grate and turn it in the same way as a wrench.
How to open the hood of a Ford Focus from the outside |
Replacing the hood latch
Read also
Do you remember the BMW Concept 4 and its giant radiator grille? Of course. The template for the next 4 episodes was created after the new episodes X7 and 7 with a cell size of the month. Whether you like it or not, it doesn't matter as BMW has already said that ...
Headlight for Nissan X trail T31, Tiida, Nout, Beetle, Pathfinder and Primera The effectiveness of a set of lighting programs directly affects safety road traffic in the dark and with poor visibility, so our client stays with the items for granted ...
How to clean and clean a gas pump in Megana 2, a repair manual There are several signs that need to be repaired or Renault vehicles: Megan won't start, you can hear the rumble to heaven ...
We pitted our long-running Pacifica hybrid against Toyota Riding and handling For all the reasons Sienna chose the newer competition. four-wheel drive should be accessible. My tester was so equipped and I got the opportunity to experience ...
Compact Daewoo matiz is a representative budget segment... Therefore, motorists prefer to carry out most of the work on maintenance... Replacing antifreeze is also a simple operation if you follow the instructions ...
Replace fuel filter Kia Sportage The fuel filter is the main device responsible for preventing foreign objects (dust, rust) from entering the fuel system engine. If this filter did not exist, our client would have ...
And the hood is open! As a rule, the locking antennas, the mounting antennas that you see in the photo above, wear out or break. And the gimbal is already jumping out of place at every turn of the key and trying to open the hood. To do this, either replace the lock cylinder, or insert the cardan into place and wrap it with electrical tape, or better yet. Solder the gimbal and the larva.
How to open the hood of a Ford Focus 2: 8 comments
Is it possible to remove the underside crankcase and bumper protectors to get into the lock?
Sure. Below is it removed
the protection can also have a bumper on the bottom, and it must be unscrewed from the top, since it is necessary to remove the light. Nikolay.
Hi, I broke the antenna socket where the gimbal was inserted. what should I do? Thanks to.
Hi are you talking about gimbal or hooded lock?
Hello! I have the same misfortune, except that the alloy that you called "traction" is slightly different, it is not plastic, but in the form of a cable (rubber on top, in the middle of an iron blade). The first case of this "discovery" took place about six months ago. Then he found information on how to open a screwdriver, put it on this cable and push hard (on the white core), at which point a friend turned the key. It happened! The hood opened, the mechanism was assembled, everything worked. Until recently. Again the same story, only now the screwdriver does not help: he too is exhausted, his friends too. This is not all. I found the theme like a peasant with a hot screwdriver, toasted the same white core, and then this screwdriver is the key. Only no one says, as before, he removed this cable (traction), which would then be right in the center. I nervously pulled this cable, it was split into two halves: the upper rubber part remained on the key side, and the iron center on the engine side. In short, I don't know what to do next, I would like to try frying, but I don't know how to remove this cable, can someone tell me?
When the author bumped into the gimbal, he jumped out of the groove and, to his surprise, found an even easier way to break the hood without a key.
The illustration showing the inserted screwdriver clearly shows the protective plastic mesh. This grid can be partially removed from the mounting grooves with bare hands and without damage, and then, entering the gap formed between the machine body and this grid, move your hand or hands and insert the gimbal into the groove. And you can, by inserting into one groove, pulling the mask, scroll in one direction and the veil in the other direction, the hood will unlock.
Gratitude! They saved the girl today. died right in front of the Bolshoi Theater.
Post Views: 15
Plastic is the enemy of reliability. Realizing this perfectly, car manufacturers persistently continue to use it in loaded nodes. On the second generation Ford Focus, plastic parts are also found quite often, and in the most unexpected places. For example, the hood lock. The locking mechanism itself is made of metal, but its drive is plastic. How to open the hood on Ford Focus 2 if the lock is broken, let's think together.
On the second generation of the Focus, the hood latch actuator is designed differently from most cars.
We are accustomed to the fact that the latch of the lock is set in motion by a cable laid under the hood. It can end with a hood opening handle, and manual mechanism can be duplicated by limit switches central locking. On the second Focus, the hood lock can only be unlocked from the street and with a key - we discard the blue oval on the grill, insert the key into the lock cylinder, turn the key half a turn counterclockwise, raise the hood, turn the key half a turn clockwise, and only then the hood can be opened.
The hood lock mechanism Ford Focus 2 contains several plastic rods.
The mechanism, to put it mildly, is not the most ideal, but there is nowhere to go, you have to live with it.
Another feature of the Ford lock on Focus is the presence of several plastic rods that are not reliable.
According to the owners, often the thrust that goes from the larva to the lock latch simply wears out and comes out of engagement with the groove. As a result, we rotate the key, but nothing happens, the lock is locked.
The lock is broken, what should I do?
There are several options for opening the hood lock if it does not want to open it with a key. The lock, as a rule, has nothing to do with it, since it is metal and rarely gets jammed. It's all about the plastic rods and plastic elements of the larva's structure. If the rod itself has broken or worn out, you can try to install it in place from under the car.
One of the reasons for the failure of the bonnet lock is the plastic pull.
To do this, remove the engine protection and get access to the lock from below. At least you can see what is happening with the mechanism by shining a flashlight. From below, you can throw the traction into place and open the hood, and after that it is already possible to carry out diagnostics. The problem is that the pull rod is not sold separately, only complete with a lock. But since the lock itself rarely breaks, then it practically does not exist on sale, you can find a lock in parts only during disassembly, and a new lock assembly costs at least 3 thousand rubles.
Necessary tools to open the lock.
The second option is more barbaric, but if there is no other way out, and it is necessary to open the hood, we will use it. To open the lock, we need a long (300-400 mm) flat-head screwdriver, flashlight, gas burner(or any other source of fire or heat).
Open the hood lock with a long screwdriver.
We do this:
- We shine a flashlight towards the lock through the radiator grill, understand the structure and visually find the central plastic heel of the lock, into which the thrust from the larva should enter.
- We warm up the tip of the screwdriver with a gas burner and carefully insert it between the ribs of the grate.
- Press with a hot screwdriver on the plastic heel of the lock so as to melt the groove. At the same time, we press the screwdriver as hard as possible and try to get into the center of the plastic part.
- We hold the screwdriver in this position for a few seconds, when the screwdriver cools down, take it out.
- As soon as the screwdriver cools down, we again fall with the sting into the new groove that we just melted, and turn the lock in the same way as with the key - counterclockwise, raise the hood, clockwise, open the hood completely.
After opening the hood, you can replace the lock or pull the cable into the car interior.
We opened the hood, now you can either use a screwdriver for a while instead of the key, or pull the cable into the cabin and open the lock from there. Yet again, it is always possible to buy either a new or used lock for the Focus on disassembly... Good luck to everyone and lubricate the locks more often!
Video how to open the hood and change the disguise to Ford Focus 2
Several other questions that they ask me can be attributed to the same topic: "without a key", "Open the hood of a Ford Focus 1", "How to open the hood ford mondeo"," Like a Ford "and so on. I'll show you using my Focus 2 as an example ...
How to open the hood of FF2
The hood of Ford Focus 2 is opened with the ignition key. There is no cable here, and it is not possible to open it from the passenger compartment (at least in this configuration). First, let's figure out how the Ford Focus hood lock works, in particular, the Ford Focus 1 hood lock and the Ford Focus 2 hood lock.
How to open the hood of a Ford
As we can see in the photo above, you need to insert the bonnet ignition key into the lock cell under the "Ford" logo on the radiator grill, which must be turned up and left. After inserting the key, as indicated in the instructions (seen in the photo), first turn it counterclockwise (left) half a turn, while simultaneously pulling the hood up, and immediately turn the key half a turn clockwise (right) - the hood is open.
See the photo above. Since the radiator grille is located far from the hood lock itself, while we turn the key, we turn this (red arrow) rod, which, in fact, opens the lock. As a rule, the cylinder of the bonnet lock breaks. People, as a rule, immediately run screaming - the hood lock has broken, buy a Ford Focus hood lock! But, it breaks, neither the lock, nor the rod is broken, this rod (pictured above) simply jumps out of the groove.
But don't worry! The hood can be opened manually by inserting the rod into place and turning this rod from the bottom of the car, having previously disassembled the engine protection (see two photos below)
How to open the hood of a Ford
Or… Insert a long flat screwdriver through the radiator grill and turn it in the same way as with a key.
How to open the hood of a Ford Focus from the outside
And the hood is open! As a rule, the fixing antennae of the gimbal socket, which you see in the photo above, wears out or breaks. And the cardan is already jumping out of its place at every turn of the key and trying to open the hood. To do this, either change the lock cylinder, or insert the cardan into place and wrap it with electrical tape, or even better - solder the cardan and the larva.
How to Open Ford Focus Bonnet When Lock Is Broken
Source: https://korea1.ru/en/premery/kak-otkryt-kapot-na-ford-focus-kak-otkryt-kapot-na-ford-focus-ford/
0 Response to "How to Open Ford Focus Bonnet When Lock Is Broken"
Post a Comment